自動焊接機工作速度較快，深度較大，不易變形。可以同時進行多束加工和多工位加工，使焊件更加準確。下面來講講山東自動焊接設備的檢查與注意事項。

The automatic welding machine has fast working speed, large depth and is not easy to deform. Multi beam processing and multi station processing can be carried out at the same time to make the weldment more accurate. Now let's talk about the safety inspection and precautions of Shandong automatic welding equipment.

自動焊接設備檢查：

Safety inspection of automatic welding equipment:

操作員在每次焊接操作前要檢查以下項目：

The operator shall check the following items before each welding operation:

1.確保焊接機相互良好的接地是可靠的安裝。

1. Ensure that the welding machine is reliably grounded.

2.確保焊接機的輸入和輸出電纜完好無損。

2. Ensure that the input and output cables of the welding machine are intact.

3.安裝并固定了焊接機后，專門的人員要定期對其進行檢查。

3. After the welding machine is installed and fixed, special personnel shall inspect it regularly.

4.不會有內部間隙等異常情況。檢查并確認送絲輥的凹槽和齒型完好無損，并且在磨損或接觸不良時應更換輥和接觸頭塊。

4. There will be no abnormal conditions such as internal clearance. Check and confirm that the groove and tooth profile of the wire feeding roller are intact, and replace the roller and contact head block in case of wear or poor contact.

使用自動焊接設備的注意事項：

Precautions for using automatic welding equipment:

1.焊槍電纜不要壓得太緊，彎曲角度也不能太小。送絲軟管的半徑不應小于150mm，否則內部電纜會損壞，可能導致事故。焊接期間請勿更改電壓調試開關。

1. The welding gun cable shall not be pressed too tightly and the bending angle shall not be too small. The radius of wire feeding hose shall not be less than 150mm, otherwise the internal cable will be damaged, which may lead to accidents. Do not change the voltage commissioning switch during welding.

2.在焊接操作過程中，請勿觸摸帶電部件，例如焊接機的輸出接口。

2. During the welding operation, do not touch the live parts, such as the output interface of the welding machine.

3.更改或調試面板旋鈕時，請勿過分用力。自動不銹鋼管焊接機可能會損壞設備。

3. Do not use excessive force when changing or debugging the panel knob. Automatic stainless steel pipe welding machine may damage the equipment.

4.每次焊接之前，請檢查焊接機的連接是否正確以及接地線是否可靠。

4. Before each welding, please check whether the welding machine is connected correctly and whether the grounding wire is reliable.

上述是為大家介紹的使用自動焊接設備的注意事項，相信大家閱讀完文章之后對這一問題有了新的了解和認識，如果您想了解更多知識，歡迎多多關注我們的網站http://www.tinghaiwu.com動態。

The above are the precautions for the use of automatic welding equipment. I believe you will have a new understanding of this issue after reading the article. If you want to know more, please pay more attention to our website http://www.tinghaiwu.com Dynamic.